GFI Forums: Kerio Control » Kerio Control 9.2.8 is ok?

Home » GFI User Forums » Kerio Control » Kerio Control 9.2.8 is ok? (Kerio Control 9.2.8 is ok?)

Show: Today's Messages :: Show Polls :: Message Navigator
E-mail to friend

Kerio Control 9.2.8 is ok? [message #144590]

Thu, 13 December 2018 20:59

Kuro
Messages: 2
Registered: December 2018

Hi all.
Is 9.2.8 appliance release have no issues? I hope it is, don't want any adventures after update.
I haven't seen any bad reports here. if someone had some negative experience please tell me. Thank you in advance

Report message to a moderator

Re: Kerio Control 9.2.8 is ok? [message #144610 is a reply to message #144590]

Mon, 17 December 2018 17:58

Columbia
Messages: 196
Registered: August 2014
Location: Moscow

I have installed 9.2.8 three days ago. No problems so far with Kerio appliance.

Report message to a moderator

Re: Kerio Control 9.2.8 is ok? [message #144615 is a reply to message #144610]

Tue, 18 December 2018 06:47

Kuro
Messages: 2
Registered: December 2018

thanks for feedback

Report message to a moderator

Re: Kerio Control 9.2.8 is ok? [message #144619 is a reply to message #144615]

Tue, 18 December 2018 17:05

Shaunie
Messages: 23
Registered: June 2016
Location: Everywhere

I installed it two days ago no real issues. I upgraded due to every time my AV would check for updates the memory usage would spike to around 95%. Now a major issue as it only happens briefly but as management monitor all the logs they was asking questions..

When I upgraded my memory usage was steadily around 75% after upgrade the dropped as low as 27%
I have now noticed over the last few days it is steadily creeping up like there is a memory leak memory usage is now at 38%

./fa/4906/0/

Attachment: kerio.JPG
(Size: 49.55KB, Downloaded 742 times)

Report message to a moderator

Re: Kerio Control 9.2.8 is ok? [message #144626 is a reply to message #144590]

Wed, 19 December 2018 14:10

ian.bugeja
Messages: 666
Registered: March 2017
Location: Malta

9.2.8 has improved memory management that's why it consumes less memory.

I do not consider 27% to 38% a memory leak as on boot some features might have not been loaded in memory but would be loaded later.

Does the memory keep on increasing?

Ian Bugeja
GFI Software

Report message to a moderator

Re: Kerio Control 9.2.8 is ok? [message #144634 is a reply to message #144626]

Thu, 20 December 2018 23:00

fishtech
Messages: 611
Registered: September 2010

If you have an appliance make sure you check that it is still supported, otherwise you will not be able to install the update.

https://support.gfi.com/hc/en-us/articles/360013006733-Kerio -Control-Legacy-Hardware-Support

i just had to purchase a new appliance.

ft.

[Updated on: Thu, 20 December 2018 23:01]

Report message to a moderator

Re: Kerio Control 9.2.8 is ok? [message #144639 is a reply to message #144634]

Fri, 21 December 2018 11:29

Shaunie
Messages: 23
Registered: June 2016
Location: Everywhere

As of now it is at 40% I am about 2-3 hours shy of 5 full days up and running. So yes it does like its creeping up gradually.

After almost 5 days I would have though all services to be started by now :sarcasm

./fa/4908/0/

Attachment: kerio 2.JPG
(Size: 24.62KB, Downloaded 616 times)

Report message to a moderator

Re: Kerio Control 9.2.8 is ok? [message #144723 is a reply to message #144634]

Sat, 05 January 2019 03:37

MacLab
Messages: 233
Registered: May 2012

fishtech wrote on Thu, 20 December 2018 17:00

If you have an appliance make sure you check that it is still supported, otherwise you will not be able to install the update.

https://support.gfi.com/hc/en-us/articles/360013006733-Kerio -Control-Legacy-Hardware-Support

i just had to purchase a new appliance.

ft.

Interesting. They say last supported version is 9.24 yet I have installed 9.28 on several 1120 boxes and it is working fine. This was before I knew it was unsupported.

[Updated on: Sat, 05 January 2019 03:39]

Report message to a moderator

Re: Kerio Control 9.2.8 is ok? [message #144724 is a reply to message #144723]

Sat, 05 January 2019 03:44

MacLab
Messages: 233
Registered: May 2012

I would like to know what "last day of software maintenance" means. Does this mean no more protection? Or no more updates?

Report message to a moderator

Re: Kerio Control 9.2.8 is ok? [message #144725 is a reply to message #144724]

Sat, 05 January 2019 09:53

Shaunie
Messages: 23
Registered: June 2016
Location: Everywhere

MacLab wrote on Sat, 05 January 2019 03:44

I would like to know what "last day of software maintenance" means. Does this mean no more protection? Or no more updates?

I would imagine no more updates. Your product will continue to work.

Report message to a moderator

Re: Kerio Control 9.2.8 is ok? [message #144920 is a reply to message #144590]

Tue, 29 January 2019 13:15

ipsys
Messages: 38
Registered: March 2018
Location: Burkina Faso

Quote:

Hi all.
Is 9.2.8 appliance release have no issues? I hope it is, don't want any adventures after update.
I haven't seen any bad reports here. if someone had some negative experience please tell me. Thank you in advance

life is one great big adventure! hope is a good thing, but doesn't last forever ..